Back to all

When Are Your Tires Worn Out?

April 19, 2020


 

Hey Sterling Heights area drivers, are your tires worn out? What is the standard for our Michigan streets? How can you tell on your vehicle?

While there may be legal requirements for the Sterling Heights area, there are safety concerns that go beyond meeting minimum replacement mandates.

Two-thirty-seconds of an inch is the depth of the tire tread wear indicator bars that US law has required to be molded across all tires since August 1, 1968. When tires are worn so that this bar is visible, there's just 2/32 of an inch – 1.6 millimeters – of tread left. It's that level of wear that's been called into question recently.

We're referring to the tread depth on a tire, it can't move surface water out of the way and you start to hydroplane.

In a safety study, a section of a test track was flooded with a thin layer of water. If you laid a dime on the track, the water would be deep enough to surround the coin, but not enough to cover it.

A car and a full-sized pick-up accelerated to 70 miles per hour, or 112 kilometers an hour, and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths:

  • New tire tread depth
  • 4/32 of an inch, or 3.2 mm
  • 2/32 of an inch, or 1.6 mm

So what happened with the 2/32 inch/1.6 mm tires on the car? Get this – when the car had traveled the distance required to stop with new tires, it was still going 55 mph/89 kph. Stopping distance was nearly doubled to 379 feet/116 meters, and it took 5.9 seconds.

Wow! That means if you barely have room to stop with new tires, you would hit the car in front of you at 55 mph/89 kph with the worn tires.

Now, with the partially worn tires – at 4/32 of an inch, or 3.2 mm – the car was still going at 45 mph/72 kph at the point where new tires brought the car to a halt. It took nearly 100 feet, or about 30 meters, more room to stop and 1.2 seconds longer. That's a big improvement. We can see why Consumer Reports and others are calling for a new standard.

Of course, stopping distances were greater for the heavier pick-up truck.

How do you know when your tires are at 4/32 inch or 3.2 mm? Easy; just insert an American quarter into the tread. Put it in upside down. If the tread doesn't cover George Washington's hairline, it's time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.

You may remember doing that with pennies. A penny gives you 2/32 inch, or 1.6 mm, to Abraham Lincoln's head. The quarter is the new recommendation – 4/32 inch, or 3.2 mm.

How do people feel about replacing their tires earlier? Well, tires are a big ticket item and most people want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out?

For us, and we would guess for many, the answer is "no".

Sterling Tire & Auto
34701 Van Dyke Rd
Sterling Heights, Michigan 48312
586-264-7775

 

Need Service?

Request a Quote

More articles from Sterling Tire & Auto

Road Trip? Check! (Trip Inspection)

March 17, 2024

After months of postponing travel far away from home, a lot of us can't wait to hit the road and scream "Road Trip!" again. But how long has it been since the vehicle you're planning on taking has had a thorough inspection? And is it roadworthy for several days on the highway? Time to schedule a... More

TPMS: Tire Pressure Monitoring for Your Sterling Heights Vehicle

March 10, 2024

Sterling Heights drivers may know that all 2008 model year and newer cars, mini-vans and light trucks in Michigan come with a tire pressure monitoring system. Many slightly older vehicles around the Sterling Heights area have these systems as well. A tire pressure monitoring system called TPMS ... More

Let's Clear Some Things Up (Headlight Restoration)

March 3, 2024

You know how exposing your skin to sunlight can cause sunburn and other unhealthy things. Sunlight can also create major problems for your headlights. After they've been exposed to ultraviolet light, acrylic headlights can yellow and fog due to oxidation. And when that happens, less light can ... More